AS 1831-2002 pdf free

09-03 comment

AS 1831-2002 pdf free.Ductile cast iron.
3.2 Properties of the material
3.2.1 Mechanical properties
me properties of materials are given in clause 4 for machined test pieces prepared from separately cast test samples, and in clause 5 for test pieces prepared from cast-on test samples.
3.2.2 Microstructure
Where a microscopic examination is required, it shall be verified that the structure contains a minimum of 80 % of form V or VI graphite in accordance with ISO 945. The number of tests and the sampling conditions shall be defined by agreement between the purchaser and the manufacturer.
Non-destructive methods exist for testing the nodularity of the graphite and the matrix structure, which may be used, if necessary, to limit the number of micrographs to be made.
In cases of dispute, the result of the microscopic examination, which shall be carried out in accordance with an agreement between the purchaser and the manufacturer, shall prevail.
4 Requirements for separately cast test samples
4.1 Formation of batches
4.1.1 Non-continuous production
For non-continuous production, the batches shall be made up of castings made of iron originating from the same treatment ladle and, where necessary, having undergone the same heat treatment. The maximum mass of the batch shall be 2 000 kg of fettled castings. A single casting comprises a batch if its mass is equal to or greater than 2 000 kg.
4.1.2 Continuous production
For continuous production of the same grade, the maximum mass of the batch is limited to the tonnaqe Droduced in 2 h.
The test samples shall be stripped from the mould at a temperature riot exceeding 500 °C and, if necessary, they shaJl be subjected to the same heat treatment as the castings which they represent and at the same time.
If the spheroidizing treatment is carried out in the mould
(in-mould method) the test samples conforming to figure 1. 2 or
— either cast side-by-side with the castings, with a joint feeder system;
— or cast separately, with a treatment device in the mould which shall resemble that of the casting as closely as possible.
4.4 Mechanical properties
44.1 Tensile strength. proof stress, elongation and additional information
The verification of the 0,2 % proof stress values shall be determined only if specified by the purchaser at the time of ordering.
When measured on machined test pieces prepared from separately cast test samples, the mechanical properties of spheroidal grdphite cast iron shall be as specified in table 1 or 2.
4.4.2 Impact test
The specified impact values given in table 2 apply only to grades 400-18 and 350-22.AS 1831 pdf download.

Download It Now Download Here
AS NZS 60598.2.17:2019 AS pdf free download

AS NZS 60598.2.17:2019

AS NZS 60598.2.17:2019 pdf free.Luminaires Part 2.17: Particular requirements—Luminaires for stage lighting, television and film studios (outdoor and indoor). 17.7.2 The luminaires for certain types of high-intensity discharge lamp, where an explosion risk is declared by the lamp manufacturer, shall incorporate a device to prevent immediate access to the lamp after switching-off or shall be marked in accordance with the...
AS NZS 4859.1:2018 AS pdf free download

AS NZS 4859.1:2018

AS NZS 4859.1:2018 pdf free.Thermal insulation materials for buildings Part 1: General criteria and technical provisions. 2.1 GENERAL This Section provides performance criteria and technical provisions for materials to be used in the thermal insulation of buildings and building services. In addition to this Section the insulating material shall— (a) meet packaging and labelling requirements of Section 3; (b) where...
AS NZS 2442.2:2021 AS pdf free download

AS NZS 2442.2:2021

AS NZS 2442.2:2021 pdf free.Performance of household electrical appliances一Rotary clothes dryers Part 2: Energy efficiency labelling requirements. Section 2 Test requirements, calculations and algorithms for the energy rating label 2.1 General This Section sets out the test requirements, equations and procedures br calculating values of the comparative energy consumption (CEC), and star rating, which appear on an energy rating label....


Anonymous netizen Fill in information