AS 3623-1993 pdf free

03-30 comment

AS 3623-1993 pdf free.Domestic Metal Framing.
AS 3623 sets out the performance requirements, in terms of structural adequacy and serviceability, for the framing of domestic buildings of up to two storeys in height and roof pitches of up to 35°.
Alternative methods of assessing structural adequacy using either permissible stress or limit state methods are provided in Sections 2 and 3, respectively.
This Standard does not consider the effects of corrosion.
NOTES:
1 A Commentary is provided in Appendix A.
2 This Standard should be read in conjunction with AS 4055 and the relevant Parts of AS 1170.
3 In potentially corrosive environments, advice should he obtained from the respective man u facturers on appropriate protective measures.
1.3 DEFINITIONS For the purpose of this Standard, the definitions below apply.
1.3.1 Balcony—an external area. one or more metres above the ground.
1.3.2 Bearer—a sub-floor member supporting the floor joists.
1.3.3 Bracing—diagonal members or diaphragms which resist racking forces.
1.3.4 Ceiling batten—a member flxed to roof trusses or rafters to support ceiling sheeting.
1.3.5 Chord—the top and bottom members of a truss.
1.3.6 Floor joist—a member that directly supports the flooring.
1.3.7 Heel (knee)—thc connection between top and bottom truss chords.
1.3.8 Hold-down fixings—the fixings designed to resist wind forces.
1.3.9 Internal lining—the materials used for the face of internal walls or ceilings or the inner face of external walls.
1.3.10 Internal truss member (web)—a member spanning between the top and bottom chords of a roof truss.
1.3.11 Jamb stud—the stud located beside an opening in a wall frame, e.g. doorway.
1.3.12 Lintel—the horizontal stiffening member in a wall franie spanning an opening.
1.3.13 Load redistribution—the support offered to a loaded member by adjacent members carrying less load.
1.3.14 Noggin—a horizontal restraining member fixed into a wall frame to provide lateral and horizontal restraint to the studs.
1.3.15 Non-load-bearing walls—walls which are not required to carry gravity loads.
1.3.16 Plate—a member running across the top or bottom of a wall frame.
1.3.17 Racking—the force which could cause in-plane distortion of a framing module.
1.3.18 Roof or tile batten—a member fixed to roof trusses or rafters to support roof sheeting or tiles.
1.3.19 Sheet roofing—includes sheet metal tile panels.AS 3623 pdf download.

Download It Now Download Here
ATTENTION: I REALLY NEED YOUR SUPPORT.THANKS A LOT.
AS NZS 60598.2.17:2019 AS pdf free download

AS NZS 60598.2.17:2019

AS NZS 60598.2.17:2019 pdf free.Luminaires Part 2.17: Particular requirements—Luminaires for stage lighting, television and film studios (outdoor and indoor). 17.7.2 The luminaires for certain types of high-intensity discharge lamp, where an explosion risk is declared by the lamp manufacturer, shall incorporate a device to prevent immediate access to the lamp after switching-off or shall be marked in accordance with the...
Download
AS NZS 4859.1:2018 AS pdf free download

AS NZS 4859.1:2018

AS NZS 4859.1:2018 pdf free.Thermal insulation materials for buildings Part 1: General criteria and technical provisions. 2.1 GENERAL This Section provides performance criteria and technical provisions for materials to be used in the thermal insulation of buildings and building services. In addition to this Section the insulating material shall— (a) meet packaging and labelling requirements of Section 3; (b) where...
Download
AS NZS 2442.2:2021 AS pdf free download

AS NZS 2442.2:2021

AS NZS 2442.2:2021 pdf free.Performance of household electrical appliances一Rotary clothes dryers Part 2: Energy efficiency labelling requirements. Section 2 Test requirements, calculations and algorithms for the energy rating label 2.1 General This Section sets out the test requirements, equations and procedures br calculating values of the comparative energy consumption (CEC), and star rating, which appear on an energy rating label....
Download

LEAVE A REPLY

Anonymous netizen Fill in information