AS ISO 10322.1:2017 pdf free

02-25 comment

AS ISO 10322.1:2017 pdf free.Ophthalmic optics – Semi-finished spectacle lens blanks, Part 1: Specifications for single-vision and multifocal lens blanks.
Compared with previous editions, this part of ISO 10322 now applies to all types of semi-finished singlevision and multifocal lens blanks.
This part of Iso 10322 specifies requirements for the optical and geometrical properties of all semifinished single-vision and multifocal spectacle lens blanks.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 7944, Optics and optical instruments — Reference wavelengths
ISO 8598-1, Optics and optical instrunents — Focimeters — Part 1: General purpose instruments
ISO 13666, Ophthalmic optics — Spectacle lenses — Vocabulary
4 Classification
Semi-finished lens blanks (shortened to lens blanks in the remainder of this part of ISO 10322 for easier reading) are classified according to the finished surface as follows:
a) single-vision lens blanks;
b) multifocal lens blanks;
c) progressive-power and degressive-power lens blanks.
5 Requirements
5.1 General
The tolerances shall apply at a temperature of 23 °C ± 5 °C.
5.2 Optical requirements for the finished surface
5.2.1 General
The optical tolerances shall apply to the manufacturer’s stated values at the reference points of the lens blank at one of the reference wavelengths specified in Iso 7944.
The reference point should be specified by the manufacturer. If no reference point is specified, the blank’s geometric centre may be assumed to be the reference point.
The optical tolerances in Tables 1., 2. and 3 are expressed as surface power values, in dioptres, in the refractive index of the material of the lens blank being measured.
5.2.3 Uniformity of the surface power of lens blanks with nominally spherical surfaces
Over a zone of 40 mm diameter centred around the reference point, the surface power shall not deviate by more than 0,06 D from the surface power measured at the reference point.
The uniformity shall be determined using a suitable instrument and the method described in 6.2.
5.2.4 Tolerances on the intended surface cylindrical power
The tolerances on the intended surface cylindrical power as specified in Table 2 shall apply at the reference point and shall be measured using the method described in 6.2.

Download It Now Download Here
AS NZS 60598.2.17:2019 AS pdf free download

AS NZS 60598.2.17:2019

AS NZS 60598.2.17:2019 pdf free.Luminaires Part 2.17: Particular requirements—Luminaires for stage lighting, television and film studios (outdoor and indoor). 17.7.2 The luminaires for certain types of high-intensity discharge lamp, where an explosion risk is declared by the lamp manufacturer, shall incorporate a device to prevent immediate access to the lamp after switching-off or shall be marked in accordance with the...
AS NZS 4859.1:2018 AS pdf free download

AS NZS 4859.1:2018

AS NZS 4859.1:2018 pdf free.Thermal insulation materials for buildings Part 1: General criteria and technical provisions. 2.1 GENERAL This Section provides performance criteria and technical provisions for materials to be used in the thermal insulation of buildings and building services. In addition to this Section the insulating material shall— (a) meet packaging and labelling requirements of Section 3; (b) where...
AS NZS 2442.2:2021 AS pdf free download

AS NZS 2442.2:2021

AS NZS 2442.2:2021 pdf free.Performance of household electrical appliances一Rotary clothes dryers Part 2: Energy efficiency labelling requirements. Section 2 Test requirements, calculations and algorithms for the energy rating label 2.1 General This Section sets out the test requirements, equations and procedures br calculating values of the comparative energy consumption (CEC), and star rating, which appear on an energy rating label....


Anonymous netizen Fill in information