BS EN 1176-7:2020 pdf free

05-14 comment

BS EN 1176-7:2020 pdf free.Playground equipment and surfacing.Guidance on installation, inspection, maintenance and operation.
BS EN 1176-7 1 Scope This document is applicable to playground equipment, surfacing and ancillary items, e.g. gates, fences, benches, bins, shades, etc. It is intended for use by playground operators (see definitions 3.4) to assist them in developing an inspection and maintenance regime for each playground. NOTE 1 The scope of the inspection and inclusion of the ancillary items will vary individually. NOTE2 Ancillary items are not included in the specific equipment-type parts of the EN 1176 series; hence they are not assessed for compliance with EN 1176 series and are subject to risk assessment. This document establishes guidance on the installation, inspection,  aintenance and operation of playground equipment and surfacing around the equipment. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1176-1:2017, Playground equipment and surfacing 一Part 1: General safety requirements and test methods EN 1177:2018, Impact attenuating playground surfacing一Methods of test for determination of impact attenuation.3.1 inspection check to ensure the continuous safe use of a playground NOTE The purpose of an inspection is to assess the overall level of safety of the equipment and/or surfacing of the playground. The outcome of an inspection is reported in an inspection report and can result in preventive measures such as extra maintenance, repairs, etc. 3.2 maintenance intervention that is required and/or undertaken to conserve, as nearly and as long as possible, the original condition of the equipment and surfacing while compensating for normal wear and tear NOTE The maintenance instructions are provided by the supplier as stated in EN 1176-1:2017, 6.1.4 3.3  competent person person, suitably trained, qualified by knowledge and practical experience to carry out the required task Note 1 to entry: Levels of knowledge required by different levels of inspectors to be competent are given in e.g. CEN/TR 17207:2018, 5.1, and/or national specifications. Note 2 to entry: A competent person might be the operator, inspector, employee of the manufacturer or else.BS EN 1176-7 pdf download.

Download It Now Download Here
ATTENTION: I REALLY NEED YOUR SUPPORT.THANKS A LOT.
BS ISO 24081:2021 pdf download BS pdf free download

BS ISO 24081:2021 pdf download

BS ISO 24081:2021 pdf download.Ground cassava leaves (Isombe) — Specification. 1 Scope This document specifies requirements and methods of sampling and testing for ground cassava leaves, which are obtained from the processing of fresh cassava leaves (Manihot esculenta Crantz or Manihot glaziovii) intended for human consumption. 2 Normative references The following documents are referred to in the text in such...
Download

BS EN 1463‑2:2021

BS EN 1463‑2:2021 pdf download.Road marking materials — Retroreflecting road studs Part 2: Road test performance specifications. 4 Test sites and conditions 4.1 General Test sites shall be arranged at suitable locations that meet at least the requirements of 4.2 to 4.5. The test results will depend on the weather, traffic and road surface conditions. These shall all be described...
Download
BS ISO 3739‑2:2021 pdf download BS pdf free download

BS ISO 3739‑2:2021 pdf download

BS ISO 3739‑2:2021 pdf download.Industrial tyres and rims Part 2: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims — Load ratings. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited...
Download

LEAVE A REPLY

Anonymous netizen Fill in information