BS ISO 21780:2020 pdf free

05-06 comment

BS ISO 21780:2020 pdf free.Road vehicles一Supply voltage of48 V一Electrical requirements and tests.
BS ISO 21780 The test procedure shall be defined in conjunction with the customer and documented within a test plan. For each test, as applicable, the permitted error memory entries and the functional statuses for each function of the component shall be agreed with the customer and documented within the test plan. Details of the test setup, operating loads (e.g. triggering, original sensors, original actuators and replacement circuitry) and the required boundary conditions shall be agreed between the customer and the supplier and documented in a test plan and in the resultant test report. Components that are electrically both a source and a sink shall be tested in both modes of operation.The test equipment shall ensure that all interfaces which are required to meet the specified performance of the DUT are populated and functional to the required level. Signals or messages which shall be received from or transmitted to the vehicle controller in order to ensure the DUT functions as expected may be simulated if a full vehicle or HIL simulation is not used.In all cases, program and data storage devices shall remain in FS1 until the component is deactivated.If the device has non-volatile memory, the integrity (not the current status) of the non-volatile memory shall be ensured at all times.Damage to the DUT is not permitted in FS1 to FS4. The permissible limit values specified in the data sheets (e.g. electrical, thermal or mechanical) of the electric/electronic components in the DUT shall
not be exceeded. Evidence of this is provided at least by the parameter check as described in 8.9. An electrical test begins when the DUT has started up completely and is in FS1.Before and after every test, the DUTs shall be subjected to a parameter check as described in 8.9 in accordance with specifications. The DUT shall be in a steady state of temperature at the beginning
of each test.During each test, the key parameters to be monitored shall be recorded as described in 8.10. Component resets shall be monitored and documented in an appropriate form to be included in the test report.Damaged DUTs (FS5) shall be removed from the test cycle, analysed regarding the root cause for the failure and documented. In such cases, the test shall be repeated with a new DUT, or the following test in the test plan shall be performed with a new DUT. The procedure shall be agreed with the customer.The physical analysis as described in 8.11 shall be carried out on at least one DUT following completion of all the electrical tests. All component parts including hardware, software or calibrations of the DUT undergoing final validation stage, shall be recorded. Any change in these parts shall require revalidation or justification of no impact.BS ISO 21780 pdf download.

Download It Now Download Here
ATTENTION: I REALLY NEED YOUR SUPPORT.THANKS A LOT.
BS ISO 24081:2021 pdf download BS pdf free download

BS ISO 24081:2021 pdf download

BS ISO 24081:2021 pdf download.Ground cassava leaves (Isombe) — Specification. 1 Scope This document specifies requirements and methods of sampling and testing for ground cassava leaves, which are obtained from the processing of fresh cassava leaves (Manihot esculenta Crantz or Manihot glaziovii) intended for human consumption. 2 Normative references The following documents are referred to in the text in such...
Download

BS EN 1463‑2:2021

BS EN 1463‑2:2021 pdf download.Road marking materials — Retroreflecting road studs Part 2: Road test performance specifications. 4 Test sites and conditions 4.1 General Test sites shall be arranged at suitable locations that meet at least the requirements of 4.2 to 4.5. The test results will depend on the weather, traffic and road surface conditions. These shall all be described...
Download
BS ISO 3739‑2:2021 pdf download BS pdf free download

BS ISO 3739‑2:2021 pdf download

BS ISO 3739‑2:2021 pdf download.Industrial tyres and rims Part 2: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims — Load ratings. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited...
Download

LEAVE A REPLY

Anonymous netizen Fill in information