BS ISO 7211-6:2020 pdf free

05-02 comment

BS ISO 7211-6:2020 pdf free.Textiles – Methods for analysis of woven fa brics construction. Determination of the mass of warp and weft per unit area of fabric.
BS ISO 7211-6 This document specifies methods for determining the mass of the warp and weft threads per unit area of fabric after the removall of any non-fibrous matter. 2 Normative references The fllowing documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document For dated references, only the edition cited applies. For undated references, the latest editon of the referenced document (including any amendments) applies. ISO 139. Textiles – – Standand  tmospheres for conditioning and testing ISO 1833-1 Textiles一Quntitotive chemical enobysis一Part 1: Gemeral principles of testing
3 Terms and definitions No terms and definitions are listed in this document. IS0 and IEC maintain terminological databases for use in standardization at the fllowing addresses IS0 Online browsing platform: ailable at http:www.iso.org/obp IEC Electropedia: ailablel at http://www.electropedia.org/ Principle Method A: The outine of the fabric specimen to be dissected is marked in the form of a square or rectangle, and the nonfibrous matter is removed while the marked area still forms part of a larger sample and the threads cannot, therefore, be lost from it. If the amount of nn-fibrours matter is to be determined, it is stipulated that the larger sample shall be a square cut with its diagonals parallel to the directions of the threads in the fabric. If the amount of non-fibrous matter has not to be determined. the larger sample may be of any shape or size. Method B: A specimen of known area is dissected and the non fibrous matter is removed from the warp and weft threads. Determine the mass of the marked area to an accuracy of 0,1 %。Working over paper of a colour suitable for showing up fragments of the yarn and fibre from the fabric being tested, fray out from one edge of the square or rectangle, and collect together the threads more easily removed from the fabric.From time to time, cut off the fringe of threads remaining in the other direction of the fabric and collect the short lengths together, keeping them separate from the more easily removed threads. When the whole of the marked area has been dissected into warp and weft threads, determine the mass of the
two sets of threads separately to an accuracy of 0,1 %. The sum of these two masses shall not differ from the mass of the fabric before dissection by more than 1 %. Where the sum of the masses of warp and weft threads differs by more than 1 % from the mass of the fabric specimen, the procedure has not been followed with sufficient accuracy. Repeat the procedure in order to achieve the required accuracy. Long rectangular specimens are easier to dissect than squares, but the dissection of the latter may be facilitated by cutting into several rectangles with their lengths in the direction of the threads more easily removed from the fabric. BS ISO 7211-6 pdf download.

Download It Now Download Here
ATTENTION: I REALLY NEED YOUR SUPPORT.THANKS A LOT.
BS ISO 24081:2021 pdf download BS pdf free download

BS ISO 24081:2021 pdf download

BS ISO 24081:2021 pdf download.Ground cassava leaves (Isombe) — Specification. 1 Scope This document specifies requirements and methods of sampling and testing for ground cassava leaves, which are obtained from the processing of fresh cassava leaves (Manihot esculenta Crantz or Manihot glaziovii) intended for human consumption. 2 Normative references The following documents are referred to in the text in such...
Download

BS EN 1463‑2:2021

BS EN 1463‑2:2021 pdf download.Road marking materials — Retroreflecting road studs Part 2: Road test performance specifications. 4 Test sites and conditions 4.1 General Test sites shall be arranged at suitable locations that meet at least the requirements of 4.2 to 4.5. The test results will depend on the weather, traffic and road surface conditions. These shall all be described...
Download
BS ISO 3739‑2:2021 pdf download BS pdf free download

BS ISO 3739‑2:2021 pdf download

BS ISO 3739‑2:2021 pdf download.Industrial tyres and rims Part 2: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims — Load ratings. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited...
Download

LEAVE A REPLY

Anonymous netizen Fill in information