en 14566 pdf

04-05 comment

BS EN 14566 specifies the characteristics and performance of mechanical fasteners, including nails, screws and staples, intended to be used for the fixing of gypsum plasterboard, gypsum boards with fibrous reinforcement, products from secondary processing and suitable ancillary products as shown in Figure 2, to timber and metal, as appropriate, in building construction works. The fasteners secure the board to the framing enabling its surface to be finished by jointing or plastering to receive decoration. They can also be used for the constwction of the framing and for the connection between substructure and load bearing components and for fixing boards together. Mechanical fasteners contribute to the stability of the assembly.
This European Standard covers the following product performance characteristics: reaction to fire and flexural strength to be measured according to the corresponding European test methods.
It provides for the evaluation of conformity of the product to this European Standard.
This European Standard also covers the additional technical characteristics that are of importance for the use and acceptance of the products by the construction industry and the reference tests for these characteristics.
This European Standard does not cover nails, screws and staples intended for use with materials other than plasterboard and the plasterboard based products referred to above and their associated system components.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 338, Structural timber — Strength classes
EN 520, Gypsum plasterboards — Definitions, requirements and test methods
EN 10016 (all parts), Non-alloy steel rod for drawing and/or cold rolling
EN 10230-1, Steel wire nails — Part 1. Loose nails for general applications
EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming — Technical delivery conditions
EN 14195, Metal framing components for gypsum plasterboard systems — Definitions, requirements and test methods
EN ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, 7) (ISO 6508-1:2005)
4 Requirements
4.1 Reaction to fire
Plasterboard nails, screws and staples made from steel are classified Al (EN 13501-1) (no contribution to fire) without testing when they are not coated.
When they have an organic coating, their contribution to reaction to fire in end use condition is so small in the total assembly that they have no influence on the classification of the system tested.
4.2 Flexural strength (bending behaviour)
When tested in accordance with 5.5 no fastener shall show signs of breakage or cracking.
4.3 Release of (regulated) dangerous substances.en 14566 pdf download.

Download It Now Download Here
BS ISO 24081:2021 pdf download BS pdf free download

BS ISO 24081:2021 pdf download

BS ISO 24081:2021 pdf download.Ground cassava leaves (Isombe) — Specification. 1 Scope This document specifies requirements and methods of sampling and testing for ground cassava leaves, which are obtained from the processing of fresh cassava leaves (Manihot esculenta Crantz or Manihot glaziovii) intended for human consumption. 2 Normative references The following documents are referred to in the text in such...

BS EN 1463‑2:2021

BS EN 1463‑2:2021 pdf download.Road marking materials — Retroreflecting road studs Part 2: Road test performance specifications. 4 Test sites and conditions 4.1 General Test sites shall be arranged at suitable locations that meet at least the requirements of 4.2 to 4.5. The test results will depend on the weather, traffic and road surface conditions. These shall all be described...
BS ISO 3739‑2:2021 pdf download BS pdf free download

BS ISO 3739‑2:2021 pdf download

BS ISO 3739‑2:2021 pdf download.Industrial tyres and rims Part 2: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims — Load ratings. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited...


Anonymous netizen Fill in information