ISO 8675:1999 pdf free

03-08 comment

ISO 8675:1999 pdf free.Hexagon thin nuts (chamfered) with metric fine pitch thread — Product grades A and B.
This International Standard is part of the complete ISO product standard series on external hexagon drive fasteners. The series comprises:
a) hexagon head bolts (ISO 4014 to ISO 4016 and ISO 8765);
b) hexagon head screws (ISO 4017, ISO 4018 and ISO 8676);
c) hexagon nuts (ISO 4032 to ISO 4036, ISO 8673 to ISO 8675);
d) hexagon bolts with flange (ISO 4162 and ISO 15071);
e) hexagon nuts with flange (ISO 4161 and ISO 10663);
f) structural bolts and nuts (ISO 4775, ISO 7411 to ISO 7414 and ISO 7417).
This International Standard specifies the characteristics of hexagon thin nuts (chamfered), with metric fine pitch thread, with nominal thread diameters d from 8 mm up to and including 64 mm, with product grade A for sizes d up to and including 16 mm and product grade B for sizes d over 16 mm.
If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, for example ISO 724, ISO 898-6, ISO 965-1, ISO 3506-2 and ISO 4759-1.
Coarse thread hexagon nuts according to Iso 4035 should be the first choice.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
ISO 225:1983, Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions. ISO 724:1993, ISO general-purpose metric screw threads — Basic dimensions.
ISO 898-6:1994, Mechanical properties of fasteners — Part 6: Nuts with specified proof load values — Fine pitch thread.
ISO 965-1:1998, ISO genera/purpose metric screw threads — Tolerances — Part 1: Principles and basic data.
ISO 3269, Fasteners — Acceptance inspection.
ISO 3506-2:1997, Mechanical properties of corrosion-resistant stainless-steel fasteners — Part 2: Nuts.
ISO 4042:1999, Fasteners — Electroplated coatings.

Download It Now Download Here
BS EN 197-5:2021 pdf download BS pdf free download

BS EN 197-5:2021 pdf download

BS EN 197-5:2021 pdf download.Cement Part 5: Portland-composite cement CEM II/C-M and Composite cement CEM VI. 6 Standard designation Cements covered by this document shall be designated by at least the notation of the cement type as specified in Table 1 and the Figures 32,5, 42,5 or 52,5 indicating the strength class. In order to indicate the early strength class...
BS ISO 50009:2021 pdf download BS pdf free download

BS ISO 50009:2021 pdf download

BS ISO 50009:2021 pdf download.Energy management systems — Guidance for implementing a common energy management system in multiple organizations. 4 Context of the energy management group 4.1 Understanding the energy management group and its context Members of the EnMG (referred to in this document as the “constituent organizations”) have agreed to manage their energy use collaboratively to improve energy performance...
BS ISO 6727:2021 pdf download BS pdf free download

BS ISO 6727:2021 pdf download

BS ISO 6727:2021 pdf download.Road vehicles — Motorcycles and mopeds — Symbols for controls, indicators and tell-tales. 4.10 Letters and numerals may be used as symbols, but are not registered by ISO/TC 145, Graphical symbols, or published in ISO 7000. For example, the letters R, N, D, listed as symbols <MG.01 to MG.03>, have the meaning indicated when used in...


Anonymous netizen Fill in information