AS/NZS 60335.2.23:2017 pdf free.Household and similar electrical appliances - Safety - Part2.23:Particular requirements for appliances for skin or hair care. It has been assumed in the drafting of this International Standard that the execution of its provisions is entrusted to appropriately qualified and experienced persons. This standard recognizes the internationally accepted level of protection against hazards such as electrical, mechanical,...
AS/NZS 4765:2017 pdf free Modified PVC (PVC-M) pipes for pressure applications
AS/NZS 4765:2017 pdf free.Modified PVC (PVC-M) pipes for pressure applications. 1.1 SCOPE This Standard specifics requirements for pipes. integral joints and post-formed bends of PVC-M for the conveyance of water and wastewater under pressure. The pipes are intended for installation below ground. and above ground where they are not exposed to direct sunlight. Appendix G sets out additional requirements for...
AS/NZS 1477:2017 pdf free
AS/NZS 1477:2017 pdf free.PVC pipes and fittings for pressure applications. This Standard specifies requirements for PVC pipes and fittings for pressure applications for use below ground or above ground, where they are not exposed to direct sunlight. Appendix B sets out additional requirements for pipes and fittings classed as best environmental practice PVC-U for pressure applications. NOTE: Requirements for the...
AS/NZS 3008.1.1:2017 pdf free
AS/NZS 3008.1.1:2017 pdf free.Electrical installations - Selection of cables - Part1.1:Cables for alternating voltages up to and including 0.6/1 kV - Typical Australian installation conditions. This Standard sets out a method for cable selection for those types of electrical cables and methods of installation that are in common use at working voltages up to and including 0.6/1 kV at 50...
AS 4809:2017 pdf free
AS 4809:2017 pdf free.Copper pipe and fittings - Installation and commissioning. 1 SCOPE This Standard specifies requirements for the selection, installation and commissioning of copper plumbing. gas and waste water systems. Some aspects of design are also specified. 2 REFERENCED DOCUMENTS A list of the documents referred to in this Standard, is given in Appendix A. 3 DEFINITIONS For the...
AS 3896:2017 pdf free
AS 3896:2017 pdf free.Waters - Examination for Legionella spp - including Legionella pneumophila. This Standard sets out a method for isolating and estimating the number of Legionelia pneumophila and a range of other Legionella spp. in water. This method is applicable to all water samples. including recreational, industrial, waste and natural waters. NOTES: I A flow chart of the procedure...
AS 4177.5-2004 pdf free
AS 4177.5-2004 pdf free.Caravan and light trailer towing components - Part 5: Electrical connectors. This Standard specifies requirements for the compatibility and performance of electrical connectors for making detachable electrical connections between motor vehicles and trailers fitted with electrical equipment normally operating at a nominal d.c. voltage of 6 V, 12 V or 24V. The method of testing the performance...
AS 4177.2-2004 pdf free
AS 4177.2-2004 pdf free.Caravan And Light Trailer Towing Components - Part2:50 Mm Towballs. This Standard is Part 2 of AS 41 77. Caravan and light trailer towing components, which is published in Parts as follows: Part 1: Towbars and towing brackets Part 2: 50 mm towballs (this Standard) Part 3: Coupling body for ball couplings Part 4: Safety chains up...
AS/NZS 4968.1:2003 pdf free
AS/NZS 4968.1:2003 pdf free.Heavy-road vehicles - Mechanical coupling between articulated vehicle combinations - Part1:Design criteria and selection requirements for fifth wheel, kingpin and associated equipment. This Standard sets out the attachment design forces for fifth wheel assembly and equations to determine the required D-value of components for various combinations. This Standard applies to fifth wheel assemblies used with 50 mm,...
AS 3507.1-2003 pdf free
AS 3507.1-2003 pdf free.Non-destructive testing - Part1:Guide to radiography for ferrous castings. Diagnosis of the nature of discontinuities located by radiography can only be made by consideration of both metallurgical and radiographic factors. Consideration should therefore be given to the method of manufacture of the casting under test, and the type, position and probable distribution of any discontinuities likely to...