ASTM F434-93(2017) pdf free.Standard Test Method for Blow-Out Testing of Preformed Gaskets. ASTM F434 covers the determination of the resistance against blow-out of preformed gaskets. The test is conducted under ambient conditions and should be used for comparison purposes only to select suitable designs and constructions for specific applications. 5. Test Spedmen 5.1 The specimen shall be a 102 mm...
ASTM A106-02a pdf free
ASTM A106-02a pdf free.Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service. This specification covers seamless carbon steel pipe for high-temperature service (Note 1) in NPS 1/8 to NPS 48 inclusive, with nominal (average) wall thickness as given in ANSI B 36.10. It shall be permissible to furnish pipe having other dimensions provided such pipe complies with all other...
ASTM D4541-02 pdf free
ASTM D4541-02 pdf free.Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers. ASTM D4541 covers a procedure for evaluating the pull-off strength (commonly referred to as adhesion) of a coating system from metal substrates. Pull-off strength of coatings from concrete is described in Test Method D7234. This test offers two test protocols. Protocol 1 (test to fracture)...
ASTM A6/A6M-14 pdf free
ASTM A6/A6M-14 pdf free.Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling. This general requirements specification2 covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM: 1.2...
ASTM A182/A182M-18 pdf free
ASTM A182/A182M-18 pdf free.Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service SUPERSEDED (click for Active standard). ASTM A182/A182M covers forged low alloy and stainless steel piping components for use in pressure systems. Included are flanges, fittings, valves, and similar parts to specified dimensions or to dimensional standards,...
ASTM F3125/F3125M-19 pdf free
ASTM F3125/F3125M-19 pdf free.Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength. ASTM F3125 covers chemical, physical and mechanical requirements for quenched and tempered bolts manufactured from steel and alloy steel, in inch...
ASTM C94/C94M-15a pdf free
ASTM C94/C94M-15a pdf free.Standard Specification for Ready-Mixed Concrete. ASTM C94/C94M covers ready-mixed concrete as defined in 3.2.2 (Note 1). Requirements for quality of ready-mixed concrete shall be either as stated in this specification or as ordered by the purchaser. When the purchaser's requirements, as stated in the order, differ from those in this specification, the purchaser's requirements shall govern. This...
ASTM C109/C109M-13e1 pdf free
ASTM C109/C109M-13e1 pdf free.Standard Test Method for Compressive Strength of Hydraulic Cement Mortars. 3. Summary of Test Method 3.1 The mortar used consists of I part cement and 2.75 parts of sand proportioned by mass. Portland or air-entraining portland cements are mixed at specified water/cement ratios. Water content for other cements is that sufficient to obtain a flow of 110...
ASTM C143/C143M-10 pdf free
ASTM C143/C143M-10 pdf free. Standard Test Method for Slump of Hydraulic-Cement Concrete. ASTM C143/C143M covers determination of slump of hydraulic-cement concrete, both in the laboratory and in the field. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in...
ASTM D4318-10e1 pdf free
ASTM D4318-10e1 pdf free.Standard Test Methods For Liquid Limit, Plastic Limit, And Plasticity Index Of Soils. These test methods cover the determination of the liquid limit, plastic limit, and the plasticity index of soils as defined in Section 3 on Terminology. The methods described herein are performed only on that portion of a soil that passes the 425-μm (No. 40)...