ISO PDF Download

AS 5236.1:2021 pdf free – Cranes — Limiting and indicating devices Part 1: General

AS 5236.1:2021 pdf free.Cranes — Limiting and indicating devices Part 1: General (ISO 10245-1:2008, MOD). 4.3.2 Operating requirements 4.3.2.1 When the load on the crane exceeds the rated capacity, the rating capacity limiter shall override the controls of the crane to prevent any condition that will increase the overload. For particular crane types, reference should be made to ISO 10245-2,...

09-08

Download

AS ISO 16714:2021

AS ISO 16714:2021 pdf free.Earth-moving machinery一Recyclability and recoverability一Terminology and calculation method. In order to be recyclable, a component part or material shall be linked to a proven recycling technology. At this step, at least the following machine component parts, materials or both shall also be taken into account: — engine; — hydraulic circuit components (hydraulic pump, hydraulic control valve, swing...

09-08

Download

AS ISO 6015:2021

AS ISO 6015:2021 pdf free.Earth-moving machinery一Hydraulic excavators and backhoe loaders一Methods of determining tool forces. 4 Measurement methods 41 Test site and general The test site shall consist of a level, hard surface, with anchor points and space for using the measuring devices specified in 4.2.1 to 4.2.3. For measurements made below the ground plane, a space below that plane is...

09-08

Download

AS ISO 8925:2021

AS ISO 8925:2021 pdf free.Earth-moving machinery-Diagnostic ports. 1 Scope This International Standard defines the sizes, types and accessibility of diagnostic ports for use in measuring fluid temperature, pressure and flow, and to obtain fluid samples. It also sets out the requirements for accessibility to the port. It applies to earth-moving machinery as defined in ISO 6165, and gives general guidelines...

09-08

Download

AS 5235.1:2021 pdf free – Cranes

AS 5235.1:2021 pdf free.Cranes - Information labels Part 1: General (ISO 9942-1:2015, MOD). 1 Scope This part of Iso 9942 specifies the minimum requirements for labels for the identification (marking) and the operation of cranes. 2 Identification data 2.1 Manufacturer’s data As a minimum, the following information shall figure permanently on every crane: — name of the supplier; — name...

09-08

Download

AS ISO 8812:2021

AS ISO 8812:2021 pdf free.Earth-moving machinery - Backhoe loaders - Terminology and commercial specifications. 3.5 attachment assembly of components (3.6) that can be mounted onto the base machine (3.2) or equipment (3.3) for specific use 3.6 component part or an assembly of parts of a base machine (3.2), equipment (3.3), or an attachment (3.5) 3.7 Masses 3.7.1 operating mass OM...

09-08

Download

AS IEC 62217:2021 pdf free

AS IEC 62217:2021 pdf free.Polymeric HV insulators for indoor and outdoor use一General definitions, test methods and acceptance criteria. 7.2 Type tests The type tests are intended to verify the main characteristics of a polymeric insulator, which depend mainly on its shape and size. Type tests shall be applied to polymeric insulators belonging to an already qualified design class. The type...

09-08

Download

AS ISO 7240.1:2018 pdf download – Part 1: General and definitions

AS ISO 7240.1:2018 pdf download.Fire detection and alarm systems Part 1: General and definitions. 2.1.6 alarm signal, or condition, warning of an emergency 2.1.7 alarm indication indication

09-08

Download

AS 3856.2:2021

AS 3856.2:2021 pdf free.Hoists and ramps for people with disabilities 一Vehicle fitted Part 2: Fitting requirements. 4 General The fitting of an appliance and any modifications of a vehicle shall conform to manufacturer’s installation requirements. NOTE 1 In Australia, where applicable, Australian Design Rules and Vehicle Standard Bulletins specify requirements for the fitting of an appliance and any modifications to...

09-08

Download

AS ISO 13916:2018 standard

AS ISO 13916:2018 pdf free.Welding-Measurement of preheating temperature, interpass temperature and preheat maintenance temperature. 2 Normative references There are no normative references in this document. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform:...

09-08

Download